IBM 40/80 GB DLT Instrukcja Użytkownika

40/80 GB DLTInternal Tape DriveUser's GuideOPTIONSby IBMBe sure to read the importantmaintenance information on page 2-1.

Installing the drive in other computersFollow these steps to install the tape drive in other computers.Step 1. Selecting a SCSI IDEach device on a SCS

Step 3. Setting the SCSI ID, termination, and parityUse the following illustration to locate the SCSI configuration jumper blocks.If the tape drive is

If you choose the default SCSI address of 5, proceed to Step 4. If you need to changethe SCSI address, use the SCSI ID jumper block to set your SCSI I

To attach the SCSI and power cables to the tape drive:1. Locate the SCSI cable on your computer (a 68-pin (wide) ribbon cable with oneend connected to

If all the indicators on either side of the tape drive blink in unison, there is a problemwith the tape drive. Press the Unload button on the right si

Understanding the status indicatorsThe indicators on the right side of the drive front panel are:.1/ Write Protect (orange): When this indicator is on

.12/ 20.0 (yellow): When this indicator lights steadily, the tape is recorded at20.0 GB capacity. When this light is blinking, it indicates that you r

 The ambient operating temperature for the tape cartridge is 10°C to 40°C (50°F to104°F) and the ambient operating relative humidity (noncondensing)

The front of the cartridge has an orange write-protect indicator .1/, and awrite-protect switch .2/ to prevent accidental erasure. Slide the switch to

.5/ Press the Unload button and wait for the green Operate Handle indicator tolight..6/ Lift the Cartridge Insert/Release handle up to pop the tape ca

Note: Before using this information and the product it supports, be sure to readthe information under Appendix F, “Product warranty and notices” on p

Resetting the driveThe reset procedure rewinds the tape and clears the buffer of previous tape drivecommands and data. To reset the tape drive, press

Installation, use and maintenance guide(Translate)This guide contains product description, hardware and software installationinstructions, and product

The CDs also contain backup applications that are used with other products but are notapplicable to the 40/80 GB DLT Internal Tape Drive. Supported ta

Installing the drive in other computersFollow these steps to install the tape drive in other computers.Step 1. Selecting a SCSI IDEach device on a SCS

Step 3. Setting the SCSI ID, termination, and parityUse the following illustration to locate the SCSI configuration jumper blocks.If the tape drive is

If you choose the default SCSI address of 5, proceed to Step 4. If you need to changethe SCSI address, use the SCSI ID jumper block to set your SCSI I

To attach the SCSI and power cables to the tape drive:1. Locate the SCSI cable on your computer (a 68-pin (wide) ribbon cable with oneend connected to

If all the indicators on either side of the tape drive blink in unison, there is a problemwith the tape drive. Press the Unload button on the right si

Understanding the status indicatorsThe indicators on the right side of the drive front panel are:.1/ Write Protect (orange): When this indicator is on

.12/ 20.0 (yellow): When this indicator lights steadily, the tape is recorded at20.0 GB capacity. When this light is blinking, it indicates that you r

ContentsSafety: Read first ... ivRegistering your option ... vAbout this book ...

 The ambient operating temperature for the tape cartridge is 10°C to 40°C (50°F to104°F) and the ambient operating relative humidity (noncondensing)

The front of the cartridge has an orange write-protect indicator .1/, and awrite-protect switch .2/ to prevent accidental erasure. Slide the switch to

.5/ Press the Unload button and wait for the green Operate Handle indicator tolight..6/ Lift the Cartridge Insert/Release handle up to pop the tape ca

Resetting the driveThe reset procedure rewinds the tape and clears the buffer of previous tape drivecommands and data. To reset the tape drive, press

28 40/80 GB DLT Internal Tape Drive

Part 2: AppendixesThe following appendixes contain the POST sequence, product specifications,problem-solving information, help and service information

when your cleaning cartridge expires, make a notation on the cleaning cartridge eachtime you clean the tape drive.Appendix B. Power-on self-test (POST

Appendix C. Product specificationsThis appendix includes the product specifications and requirements.Physical specificationsHeight (with bezel) 86.3

Appendix D. Problem solvingOperating environmentTape path temperature range +10°C to +40°C(+50°F to +104°F)Relative humidity 20% to 80%, noncondensin

Tape drive failures are often caused by contamination in the tape path or by usingpoor quality media.IBM has very high quality standards for its stora

Safety: Read firstBefore installing this product, read the Safety Information.Antes de instalar este produto, leia as Informações deSegurança. Pře

Appendix E. Help and service informationSee Appendix D, “Problem solving” on page 2-4 before requesting help or service.This section contains informat

For the support telephone number and support hours by country, refer to the followingtable or to the enclosed technical support insert. If the number

Appendix F. Product warranty and notices Warranty StatementsThe warranty statements consist of two parts: Part 1 and Part 2. Part 1 varies by country.

equivalent, you may return it to your place of purchase and your money will be refunded. Thereplacement may not be new, but will be in good working or

Before IBM or your reseller exchanges a Machine or part, you agree to remove all features, parts,options, alterations, and attachments not under warra

IBM Statement of Warranty Worldwide except Canada, PuertoRico, Turkey, United States (Part 1 - General Terms) This Statement of Warranty includes Pa

LIMITATION MAY NOT APPLY TO YOU. IN THAT EVENT, SUCHWARRANTIES ARE LIMITED IN DURATION TO THE WARRANTYPERIOD. NO WARRANTIES APPLY AFTER THAT PERIOD.It

Neither IBM nor your reseller is responsible for any of your confidential, proprietary or personalinformation contained in a Machine which you return

Where IBM is in breach of a condition or warranty implied by the Trade Practices Act 1974,IBM's liability is limited to the repair or replacement

The following terms apply to the country specified:EGYPT: Limitation of Liability: The following replaces item 2 in this Section:2. as to any other ac

Pred inštaláciou tohto zariadenia si pečítaje Bezpečnostné predpisy. Antes de instalar este producto lea la información deseguridad. Läs

Applicability of suppliers and resellers (unchanged).The following paragraph is added at the end of this Section:IBM's entire liability and your

NoticesReferences in this publication to IBM products, programs, or services do not implythat IBM intends to make these available in all countries in

Electronic emission notices40/80 GB DLT Internal Tape DriveFederal Communications Commission (FCC) StatementNote: This equipment has been tested and f

Avis de conformité à la réglementation d'Industrie CanadaCet appareil numérique de classe B est conforme à la norme NMB-003 du Canada.European Un

Union Europea - Normativa EMC2-20 40/80 GB DLT Internal Tape Drive

IBMPart Number: P00N7816Printed in U.S.A.PððN7816

vi 40/80 GB DLT Internal Tape Drive

Part 1: Installation, use, and maintenanceguideThis guide contains product description, hardware and software installationinstructions, and product us

http://www.ibm.com/pc/us/solutions/accessories/tapedrives.html and follow the softwarelinks.The CDs also contain backup applications that are used wit

Installing the drive in IBM serversThe tape drive is compatible with the Netfinity 8500 or 8500R4, Netfinity 70008,Netfinity 5500, and Netfinity 5000