Ibm All-in-One Super7 Single Board Computer PCM-5896 Instrukcja Użytkownika Strona 45
- Strona / 128
- Spis treści
- BOOKMARKI
Oceniono. / 5. Na podstawie oceny klientów
Chapter 2 Installation 33
CD Audio connector (CN10)
This connector is used to connect to a CD audio cable.
CD Audio connector (CN10)
Pin Signal
1 CD_L
2 GND
3 CD_R
4 GND
Keyboard and mouse connector
(CN11)
The mainboard provides a keyboard connector which supports
both a keyboard and a PS/2 style mouse. In most cases, especially
in embedded applications, a keyboard is not used. The standard
PC/AT BIOS will report an error or fail during power-on-self-test
(POST) after a reset if the keyboard is not present. The mainboard
BIOS Advanced setup menu allows you to select "Present" or
"Absent" under the "System Keyboard" section. This allows no-
keyboard operation in embedded system applications without the
system halting under POST (power-on-self-test).
Keyboard and mouse connector (CN11)
Pin Signal
1 KB DATA
2 GND
3 MS DATA
4 N/C
5 KB CLOCK
6 Vcc
7 MS CLOCK
8 N/C
- PCM-5896 1
- FCC STATEMENT 2
- Copyright Notice 3
- Acknowledgements 3
- A Message to the Customer 4
- Product Warranty 5
- Packing list 6
- Contents 8
- Information 13
- Features 15
- Specifications 16
- 6 PCM-5896 User Manual 18
- Board layout 19
- Board dimensions 20
- Installation 21
- Jumpers and connectors 22
- Connectors 23
- Locating jumpers 24
- Locating connectors 25
- Setting jumpers 26
- CPU installing and upgrading 27
- Installing DRAM (DIMMs) 28
- Clear CMOS (J2) 29
- DOC address select (J3) 30
- COM2 Select (J6, J11) 31
- LCD clock signal select (J7) 32
- (J10, J5) 33
- Audio output select (J12) 33
- S1 (2~6) CPU Vcore select 34
- S3 (1~3) CPU clock select 35
- S3 (4~6) CPU frequency ratio 36
- Power connectors (CN8, CN1) 37
- USB connector (CN3) 38
- Connecting the hard drive 39
- 40
- Front panel connector (CN6) 41
- IrDA connector (CN7) 42
- VGA display connector (CN12) 43
- LCD connector (CN9) 44
- CD Audio connector (CN10) 45
- Keyboard and mouse connector 45
- Audio connector (CN13) 46
- Parallel port IRQ 47
- 100Base-Tx Ethernet connector 48
- Serial ports (CN16) 49
- Floppy drive connector (CN17) 50
- Ethernet active signal LED 52
- Ethernet link signal LED 52
- DiskOnChip socket (U23) 53
- Award BIOS Setup 55
- Starting setup 56
- Setup keys 57
- Getting help 58
- Main setup Menu 59
- 48 PCM-5896 User Manual 60
- Standard CMOS setup 61
- Date and Time Configuration 62
- HARD DISKS 62
- 52 PCM-5896 User Manual 64
- •Base Memory 66
- •Extended Memory 67
- •Other Memory 67
- BIOS features setup 68
- Virus Warning 69
- Quick Power On Self Test 69
- Boot Sequence 69
- 58 PCM-5896 User Manual 70
- CHIPSET features setup 72
- Auto Configuration 73
- SDRAM CAS Latency Time 73
- Memory Hole at 15M-16M 73
- 62 PCM-5896 User Manual 74
- Power management setup 75
- DEFAULTS settings 76
- Standby Mode 78
- Suspend Mode 78
- PNP/PCI configuration setup 79
- PNP OS Installed 80
- Resources Controlled By 80
- Reset Configuration Data 80
- IRQ n Assigned to 80
- DMA n Assigned to 81
- PCI IRQ Activated by 81
- Load BIOS defaults 82
- Load setup defaults 83
- Integrated peripherals setup 84
- On-Chip Primary IDE 85
- IDE Primary Master/Slave UDMA 85
- IDE HDD Block Mode 85
- On-Chip USB controller 85
- Onboard FDC Controller 86
- Onboard UART Ports (1, 2) 86
- RxD, TxD Active 86
- ECP Mode Use DMA 86
- EPP Mode select 86
- ENTER PASSWORD: 88
- CONFIRM PASSWORD: 88
- IDE HDD auto detection 89
- Save & exit setup 90
- Exit without saving 91
- 80 PCM-5896 User Manual 92
- Flat Panel/CRT 93
- Controller Display 93
- Drivers and Utilities 93
- Software drivers 94
- Necessary prerequisites 95
- Before you begin 95
- Windows® 95 96
- Select Device window 98
- 88 PCM-5896 User Manual 100
- 90 PCM-5896 User Manual 102
- Windows® 3.1 104
- the system 106
- Windows® NT 3.51 107
- Windows® NT 4.0 108
- Ethernet Software 109
- Configuration 109
- 98 PCM-5896 User Manual 110
- Audio Setup 111
- Introduction 112
- Setting Up in Windows 95 112
- 102 PCM-5896 User Manual 114
- Setting Up in NT4.0 115
- 104 PCM-5896 User Manual 116
- Programming the 117
- Watchdog Timer 117
- 106 PCM-5896 User Manual 118
- Demo program 119
- 108 PCM-5896 User Manual 120
- Installing PC/104 121
- Installing PC/104 modules 122
- Female Male 123
- PC/104 ModuleMain board 123
- 112 PCM-5896 User Manual 124
- Optional Extras 125
- PCM-10489-4 Wiring Kit 126
- Optional USB Cable 127
- 116 PCM-5896 User Manual 128
Powiązane produkty i podręczniki dla Sprzęt komputerowy Ibm All-in-One Super7 Single Board Computer PCM-5896
Sprzęt komputerowy Ibm 8306 Instrukcja Użytkownika
(314 strony)
(314 strony)
(128 strony)
Sprzęt komputerowy Ibm DS6000 Instrukcja Użytkownika
(578 strony)
(578 strony)
Sprzęt komputerowy Ibm 2 Instrukcja Użytkownika
(72 strony)
(72 strony)
© 2020, manymanuals.pl. Wszelkie prawa zastrzeżone. | 0.036 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentarze do niniejszej Instrukcji